Home > Hard Drive > HP Pavilion Seagate Hard Drive Mounting Screws Dimension/Siz.

HP Pavilion Seagate Hard Drive Mounting Screws Dimension/Siz.

Contents

Thank you. jumpers sata Hmmm i hear google works good… NOT to mention on box and back and paper instruction come with drive it clearly points out where and what the Jumpers are. Thanks for the instructions! I do have a suggestion though, could you add a few pics here and there so that we can see what you are talking about. have a peek at this web-site

I've saved this to my useful websites list for easy reference!Thanks, matey! D+ Reply Stefen Kaur on November 11, 2008 at 12:50 pm I have a question. F2 to enter Setup Utility."Can anyone tell me what I'm doing wrong? This was more than Helpfull in my Latest Conquest!!!

Internal Hard Drive Case

i have all the hook ups but the mother bord is missing the small little blue cord plug. I didnt know many of the terms either but took a few minutes to learn what they were and then followed the clear steps to install, config and run the two I connect the one with the operating system on it to SATA 1, the brnd new SATA drive to SATA 2, ad the IDE converted to SATA to SATA 3. With both drives set to Cable Select, the computer will recognize the drive hooked up to the black end connector as the master and the one hooked up to the middle

  • So you would put your disc drives on IDE2 and your hard drives on IDE1.
  • By the sixth you are talking about ‘SATA ports' and ‘SATA drives.
  • I know just enough to be dangerous to myself and all computers around me.
  • Then copy over any data you’ve stored on external drives or discs—and enjoy your companion’s new storage horizons right away.
  • what do i need to do in order to make it work in different motherboard?
  • I have no idea about computers and never opened up the box.
  • Reply Glenn on November 7, 2007 at 2:59 am Steve - if all is connected then u must format - see above under ‘Software Installation/Cloning'I've just added a second and had
  • Well it sounded so simple but no matter what I do I cannot get the computer to recognize my old drive connected to the slave connecter on the cable.

I've switched the jumpers, I've switched the drives, nothing will work. For SATA drives, your life, again, got easier. If you’re unsure of your old drive’s measurements, check the specifications online, using the model number of the drive.Most online sellers of laptop upgrade drives provide a drive-compatibility chart that lists Hard Drive Enclosure Walmart I read your page on installing and cloning my hard drives.

Reply Ravi on August 14, 2007 at 8:38 pm I need to install a Sata 160GB to my 3″ external drive, The manual does not tell much about it so is If you don't know the difference between ide & sata then you need to read up on that before trying to fit a new disk drive or you'll end up buyiing As you can guess, I took it back to the docal and he said "you fried your mother board and a small fee ($170.00) he could restore my computor and re-install All I want to do is get the info off the drive and toss it.

After finding your article, written so I could understand it, I gained the confidence I needed to do it. Internal Hard Drive Cable he said I don't know but you fried your set like a blackman handling chicken in a kitchen! ?!?!? one of the 20 GB is Primary and the other two are slaves. Two hardrives are Western Digital and one is a Maxtor.They all are marked master slave etc.

Hard Drive Enclosure Best Buy

Read more Register · Log In HP Support Forum Home > Notebooks > Hardware > HP Pavilion Seagate Hard Drive Mounting Screws Dimension/Siz... If you are adding a second drive, simply choose a connector on the same ribbon cable that is not used. Internal Hard Drive Case I have the screws that secure bracket to laptop but I do not have the screws that secure HDD to bracket. 3.5 Sata Hard Drive Enclosure I am new to SATA drives, and used to EIDE so didn't know I had to initialize it.Thanks for the help.

Reply Darklance on August 16, 2007 at 3:05 pm Thankyou for the info David.. Check This Out as i do not want to partition / reformat it. Thank you so much for this information… I was going in to my computer and to no avail didnt see the second hard drive. Reply LD on August 11, 2007 at 5:11 pm Hi, I had two hard drives installed on my computer. Hard Drive Cable To Usb

and ur write he DIDNT start off with TAKE drive out of box… jeeees…. Have done this many times for hard drives that have a ‘bad spot' that didn't allow it to be recognized on boot-up. i need help plzz Reply Pancho on December 28, 2009 at 6:37 pm Hello,I am trying to add another internal SATA 250G harddrive to my system,I have 4 plugs on my Source Do I require any jumpers on these drives if I were to hook up 2 SCSI drives together?

In Windows 2000/XP/Vista, your new drive will not appear at all in My Computer until you format it. External Hard Drive Usb Cable Much needed. I knew some of the terms, but it took a few minutes to learn what they were and then followed the clear steps to install, config and run the two drive

What size screws do I need for it?

What they need is to study "Computers for Dummies" first -then- read this article. Good job A+ on te article Reply RepairGal on January 8, 2009 at 9:42 pm Anyone who doesn't understand what a "jumper" is shouldn't be trying to change out their hard Pete and worked in Tampa "Seminole Heights" for a couple of years. External Hard Drive Carrying Case Reply Douglas on September 26, 2009 at 3:28 pm Oh My God!

If I disconnect the second drive the third one appears and vice versa. Are you sure there isn't some third type of 'standard' screw? Reply Kramium on June 28, 2008 at 10:14 pm G'day David Risley,Great help from your website! http://collinsoffice.net/hard-drive/i-need-to-replace-my-hard-drive-can-you-tell-me-what-hard-d.html System runs windows xp.If I look at the drives in computer management, both drives show up as healthy, but one is labeled "system" and the other is labeled "page files" There

Why does it matter? Reply Mark barbee on August 31, 2009 at 7:25 pm Here's one for ya. I had done everything i could think of. The hard drive that the system boots from is usually the primary master.

Reply ian on December 26, 2008 at 2:19 am hi, nice step by step, but can you tell me how can i locate the slave hard drive when it is not thanks Reply Jenna on March 20, 2009 at 1:22 pm Okay… here is my issue and I am at whits end.My hard drive crashed, but I had a back up one.